third_party/llvm-7.0/llvm/test/MC/ARM/thumb-diagnostics.s

@ RUN: not llvm-mc -triple=thumbv6-apple-darwin -o /dev/null < %s 2>&1 \
@ RUN:     | FileCheck --check-prefix=CHECK-ERRORS %s
@ RUN: not llvm-mc -triple=thumbv5-apple-darwin -o /dev/null < %s 2>&1 \
@ RUN:     | FileCheck --check-prefix=CHECK-ERRORS-V5 %s
@ RUN: not llvm-mc -triple=thumbv7m -o /dev/null < %s 2>&1 \
@ RUN:     | FileCheck --check-prefix=CHECK-ERRORS-V7M %s
@ RUN: not llvm-mc -triple=thumbv8 -o /dev/null < %s 2>&1 \
@ RUN:     | FileCheck --check-prefix=CHECK-ERRORS-V8 %s

@ Check for various assembly diagnostic messages on invalid input.

@ ADD instruction w/o 'S' suffix.
        add r1, r2, r3
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         add r1, r2, r3
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: note: invalid operand for instruction
@ CHECK-ERRORS: note: operand must be an immediate in the range [0,7]
@ CHECK-ERRORS: note: no flag-preserving variant of this instruction available

@ Instructions which require v6+ for both registers to be low regs.
        add r2, r3
        mov r2, r3
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         add r2, r3
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction variant requires Thumb2
@ CHECK-ERRORS: note: operand must be a register sp
@ CHECK-ERRORS-V5: error: instruction variant requires ARMv6 or later
@ CHECK-ERRORS-V5:         mov r2, r3
@ CHECK-ERRORS-V5:         ^

@ Immediates where registers were expected
        adds #0, r1, r2
        adds r0, #1, r2
@ CHECK-ERRORS: error: operand must be a register in range [r0, r7]
@ CHECK-ERRORS:         adds #0, r1, r2
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         adds r0, #1, r2
@ CHECK-ERRORS: note: operand must be a register in range [r0, r7]
@ CHECK-ERRORS: note: too many operands for instruction

@ Out of range immediates for ASR instruction.
        asrs r2, r3, #33
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         asrs r2, r3, #33
@ CHECK-ERRORS:                      ^
@ CHECK-ERRORS: note: operand must be an immediate in the range [1,32]
@ CHECK-ERRORS: note: too many operands for instruction

@ Out of range immediates for BKPT instruction.
        bkpt #256
        bkpt #-1
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:        bkpt #256
@ CHECK-ERRORS:             ^
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: operand must be an immediate in the range [0,255]
@ CHECK-ERRORS: note: too many operands for instruction

@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:        bkpt #-1
@ CHECK-ERRORS:             ^
@ CHECK-ERRORS: note: operand must be an immediate in the range [0,255]
@ CHECK-ERRORS: note: too many operands for instruction

@ Out of range immediates for v8 HLT instruction.
        hlt #64
        hlt #-1
@CHECK-ERRORS: error: invalid instruction
@CHECK-ERRORS:        hlt #64
@CHECK-ERRORS:        ^
@CHECK-ERRORS-V8: error: invalid instruction, any one of the following would fix this:
@CHECK-ERRORS-V8:         hlt #64
@CHECK-ERRORS-V8:              ^
@CHECK-ERRORS-V8: note: instruction requires: arm-mode
@CHECK-ERRORS-V8: operand must be an immediate in the range [0,63]
@CHECK-ERRORS: error: invalid instruction
@CHECK-ERRORS:        hlt #-1
@CHECK-ERRORS:        ^
@CHECK-ERRORS-V8: error: operand must be an immediate in the range [0,63]
@CHECK-ERRORS-V8:         hlt #-1
@CHECK-ERRORS-V8:              ^

@ Invalid writeback and register lists for LDM
        ldm r2!, {r5, r8}
        ldm r2, {r5, r7}
        ldm r2!, {r2, r3, r4}
        ldm r2!, {r2, r3, r4, r10}
        ldmdb r2!, {r2, r3, r4}
        ldm r0, {r2, sp}
        ldmia r0, {r2-r3, sp}
        ldmia r0!, {r2-r3, sp}
        ldmfd r2, {r1, r3-r6, sp}
        ldmfd r2!, {r1, r3-r6, sp}
        ldmdb r1, {r2, r3, sp}
        ldmdb r1!, {r2, r3, sp} 
@ CHECK-ERRORS: error: registers must be in range r0-r7
@ CHECK-ERRORS:         ldm r2!, {r5, r8}
@ CHECK-ERRORS:                  ^
@ CHECK-ERRORS: error: writeback operator '!' expected
@ CHECK-ERRORS:         ldm r2, {r5, r7}
@ CHECK-ERRORS:             ^
@ CHECK-ERRORS: error: writeback operator '!' not allowed when base register in register list
@ CHECK-ERRORS:         ldm r2!, {r2, r3, r4}
@ CHECK-ERRORS:               ^
@ CHECK-ERRORS-V8: error: writeback operator '!' not allowed when base register in register list
@ CHECK-ERRORS-V8:         ldm r2!, {r2, r3, r4, r10}
@ CHECK-ERRORS-V8:               ^
@ CHECK-ERRORS-V8: error: writeback register not allowed in register list
@ CHECK-ERRORS-V8:         ldmdb r2!, {r2, r3, r4}
@ CHECK-ERRORS-V8:                 ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldm r0, {r2, sp}
@ CHECK-ERRORS-V7M:                 ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldmia r0, {r2-r3, sp}
@ CHECK-ERRORS-V7M:                   ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldmia r0!, {r2-r3, sp}
@ CHECK-ERRORS-V7M:                    ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldmfd r2, {r1, r3-r6, sp}
@ CHECK-ERRORS-V7M:                   ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldmfd r2!, {r1, r3-r6, sp}
@ CHECK-ERRORS-V7M:                    ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldmdb r1, {r2, r3, sp}
@ CHECK-ERRORS-V7M:                   ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         ldmdb r1!, {r2, r3, sp}
@ CHECK-ERRORS-V7M:                    ^

@ Invalid writeback and register lists for PUSH/POP
        pop {r1, r2, r10}
        push {r8, r9}
@ CHECK-ERRORS: error: registers must be in range r0-r7 or pc
@ CHECK-ERRORS:         pop {r1, r2, r10}
@ CHECK-ERRORS:             ^
@ CHECK-ERRORS: error: registers must be in range r0-r7 or lr
@ CHECK-ERRORS:         push {r8, r9}
@ CHECK-ERRORS:              ^


@ Invalid writeback and register lists for STM
        stm r1, {r2, r6}
        stm r1!, {r2, r9}
        stm r2!, {r2, r9}
        stmdb r2!, {r0, r2}
        stm r1!, {r2, sp}
        stmia r4!, {r0-r3, sp}
        stmdb r1, {r2, r3, sp}
        stmdb r1!, {r2, r3, sp}
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         stm r1, {r2, r6}
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: error: registers must be in range r0-r7
@ CHECK-ERRORS:         stm r1!, {r2, r9}
@ CHECK-ERRORS:                  ^
@ CHECK-ERRORS-V8: error: writeback operator '!' not allowed when base register in register list
@ CHECK-ERRORS-V8:         stm r2!, {r2, r9}
@ CHECK-ERRORS-V8:                  ^
@ CHECK-ERRORS-V8: error: writeback register not allowed in register list
@ CHECK-ERRORS-V8:         stmdb r2!, {r0, r2}
@ CHECK-ERRORS-V8:                  ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         stm r1!, {r2, sp}
@ CHECK-ERRORS-V7M:                  ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         stmia r4!, {r0-r3, sp}
@ CHECK-ERRORS-V7M:                    ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         stmdb r1, {r2, r3, sp}
@ CHECK-ERRORS-V7M:                   ^
@ CHECK-ERRORS-V7M: error: SP may not be in the register list
@ CHECK-ERRORS-V7M:         stmdb r1!, {r2, r3, sp}
@ CHECK-ERRORS-V7M:                    ^

@ Out of range immediates for LSL instruction.
        lsls r4, r5, #-1
        lsls r4, r5, #32
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         lsls r4, r5, #-1
@ CHECK-ERRORS:                      ^
@ CHECK-ERRORS: note: operand must be an immediate in the range [0,31]
@ CHECK-ERRORS: note: too many operands for instruction
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         lsls r4, r5, #32
@ CHECK-ERRORS:                      ^
@ CHECK-ERRORS: note: operand must be an immediate in the range [0,31]
@ CHECK-ERRORS: note: too many operands for instruction

@ Mismatched source/destination operands for MUL instruction.
        muls r1, r2, r3
@ CHECK-ERRORS: error: destination register must match source register
@ CHECK-ERRORS:         muls r1, r2, r3
@ CHECK-ERRORS:              ^


@ Out of range immediates for STR instruction.
        str r2, [r7, #-1]
        str r5, [r1, #3]
        str r3, [r7, #128]
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         str r2, [r7, #-1]
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: invalid operand for instruction
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         str r5, [r1, #3]
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: invalid operand for instruction
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         str r3, [r7, #128]
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: invalid operand for instruction

@ Out of range immediate for SVC instruction.
        svc #-1
        svc #256
@ CHECK-ERRORS: error: operand must be an immediate in the range [0,255]
@ CHECK-ERRORS:         svc #-1
@ CHECK-ERRORS:             ^
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         svc #256
@ CHECK-ERRORS:         ^
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: operand must be an immediate in the range [0,255]


@ Out of range immediate for ADD SP instructions
        add sp, #-1
        add sp, #3
        add sp, sp, #512
        add r2, sp, #1024
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         add sp, #-1
@ CHECK-ERRORS:                 ^
@ CHECK-ERRORS: note: operand must be a register in range [r0, r15]
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         add sp, #3
@ CHECK-ERRORS:                 ^
@ CHECK-ERRORS: note: operand must be a register in range [r0, r15]
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS:         add sp, sp, #512
@ CHECK-ERRORS:                     ^
@ CHECK-ERRORS: note: operand must be a register in range [r0, r15]
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: error: instruction requires: thumb2
@ CHECK-ERRORS:         add r2, sp, #1024
@ CHECK-ERRORS:         ^

        add r2, sp, ip
@ CHECK-ERRORS: error: source register must be the same as destination
@ CHECK-ERRORS:         add r2, sp, ip
@ CHECK-ERRORS:                     ^


@------------------------------------------------------------------------------
@ B/Bcc - out of range immediates for Thumb1 branches
@------------------------------------------------------------------------------

        beq    #-258
        bne    #256
        bgt    #13
        b      #-1048578
        b      #1048576
        b      #10323

@ CHECK-ERRORS: error: branch target out of range
@ CHECK-ERRORS: error: branch target out of range
@ CHECK-ERRORS: error: branch target out of range
@ CHECK-ERRORS: error: branch target out of range
@ CHECK-ERRORS: error: branch target out of range
@ CHECK-ERRORS: error: branch target out of range

@------------------------------------------------------------------------------
@ CBZ/CBNZ - out of range immediates for branches
@------------------------------------------------------------------------------

        cbz    r0, #-2
        cbz    r0, #0
        cbz    r0, #17
        cbnz   r0, #126
        cbnz   r0, #128

@ CHECK-ERRORS-V7M: error: branch target out of range
@ CHECK-ERRORS-V7M: error: invalid operand for instruction
@ CHECK-ERRORS-V7M: error: branch target out of range
@ CHECK-ERRORS-V8: error: branch target out of range
@ CHECK-ERRORS-V8: error: invalid operand for instruction
@ CHECK-ERRORS-V8: error: branch target out of range

@------------------------------------------------------------------------------
@ SEV/WFE/WFI/YIELD - are not supported pre v6M or v6T2
@------------------------------------------------------------------------------
        sev
        wfe
        wfi
        yield

@ CHECK-ERRORS: error: instruction requires: armv6m or armv6t2
@ CHECK-ERRORS: sev
@ CHECK-ERRORS: ^
@ CHECK-ERRORS: error: instruction requires: armv6m or armv6t2
@ CHECK-ERRORS: wfe
@ CHECK-ERRORS: ^
@ CHECK-ERRORS: error: instruction requires: armv6m or armv6t2
@ CHECK-ERRORS: wfi
@ CHECK-ERRORS: ^
@ CHECK-ERRORS: error: instruction requires: armv6m or armv6t2
@ CHECK-ERRORS: yield
@ CHECK-ERRORS: ^

@------------------------------------------------------------------------------
@ PLDW required mp-extensions
@------------------------------------------------------------------------------
        pldw [r0, #4]
@ CHECK-ERRORS: error: instruction requires: mp-extensions

@------------------------------------------------------------------------------
@ LDR(lit) - invalid offsets
@------------------------------------------------------------------------------

        ldr r4, [pc, #-12]
@ CHECK-ERRORS: error: invalid instruction, any one of the following would fix this:
@ CHECK-ERRORS: note: instruction requires: thumb2
@ CHECK-ERRORS: note: instruction requires: arm-mode
@ CHECK-ERRORS: note: invalid operand for instruction

@------------------------------------------------------------------------------
@ STC2{L}/LDC2{L} - requires thumb2
@------------------------------------------------------------------------------
        stc2 p0, c8, [r1, #4]
        stc2l p6, c2, [r7, #4]
        ldc2 p0, c8, [r1, #4]
        ldc2l p6, c2, [r7, #4]
@ CHECK-ERRORS: error: invalid instruction
@ CHECK-ERRORS: error: invalid instruction
@ CHECK-ERRORS: error: invalid instruction
@ CHECK-ERRORS: error: invalid instruction

@------------------------------------------------------------------------------
@ Generic error for too few operands
@------------------------------------------------------------------------------

        adds
        adds r0
@ CHECK-ERRORS: error: too few operands for instruction
@ CHECK-ERRORS: error: too few operands for instruction

@------------------------------------------------------------------------------
@ Out of range width for SBFX/UBFX
@------------------------------------------------------------------------------

        sbfx r4, r5, #31, #2
        ubfx r4, r5, #16, #17

@ CHECK-ERRORS-V8: error: bitfield width must be in range [1,32-lsb]
@ CHECK-ERRORS-V8:         sbfx r4, r5, #31, #2
@ CHECK-ERRORS-V8:                           ^
@ CHECK-ERRORS-V8: error: bitfield width must be in range [1,32-lsb]
@ CHECK-ERRORS-V8:         ubfx r4, r5, #16, #17
@ CHECK-ERRORS-V8:                           ^

@------------------------------------------------------------------------------
@ Writeback store writing to same register as value
@------------------------------------------------------------------------------

        str r0, [r0, #4]!
        str r0, [r0], #4
        strh r0, [r0, #2]!
        strh r0, [r0], #2
        strb r0, [r0, #1]!
        strb r0, [r0], #1
        strd r0, r1, [r0], #1
        strd r1, r0, [r0], #1
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: str r0, [r0, #4]!
@ CHECK-ERRORS-V8:         ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: str r0, [r0], #4
@ CHECK-ERRORS-V8:         ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: strh r0, [r0, #2]!
@ CHECK-ERRORS-V8:          ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: strh r0, [r0], #2
@ CHECK-ERRORS-V8:          ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: strb r0, [r0, #1]!
@ CHECK-ERRORS-V8:          ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: strb r0, [r0], #1
@ CHECK-ERRORS-V8:          ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: strd r0, r1, [r0], #1
@ CHECK-ERRORS-V8:              ^
@ CHECK-ERRORS-V8: error: source register and base register can't be identical
@ CHECK-ERRORS-V8: strd r1, r0, [r0], #1
@ CHECK-ERRORS-V8:              ^